Camchat

Jump to navigation Jump to search
Showing results for camshaft. No results found for Camchat.
  • A camshaft is a shaft to which a cam is fastened or of which a cam forms an integral part. The camshaft, invented in China as early as 290 AD, was recorded
    18 KB (2,438 words) - 21:55, 31 December 2019
  • An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with
    28 KB (2,748 words) - 09:34, 14 January 2020
  • place the camshaft(s) further from the crankshaft, and in engines with multiple camshafts a timing belt or chain also enables the camshafts to be placed
    16 KB (1,935 words) - 23:01, 17 December 2019
  • chamber in the engine block. The camshaft in an OHV engine is located in the engine block. The motion of the camshaft is transferred using pushrods, and
    13 KB (1,471 words) - 13:21, 11 January 2020
  • Variable Camshaft Timing (VCT) is an automobile variable valve timing technology developed by Ford. It allows for more optimum engine performance, reduced
    6 KB (622 words) - 09:14, 24 December 2019
  • relationship between the camshaft drive (belt or chain) and intake camshaft. Engine oil pressure is applied to an actuator to adjust the camshaft position. Adjustments
    10 KB (1,290 words) - 10:54, 4 January 2020
  • the camshaft or on the crankshaft itself. This sensor is one of the two most important sensors in modern-day engines, together with the camshaft position
    5 KB (742 words) - 21:56, 21 December 2019
  • A helical camshaft is a type of mechanical variable valve actuation (VVA) system. More specifically it is a camshaft that allows the valve opening duration
    22 KB (3,483 words) - 23:10, 11 January 2020
  • Piston engines are often categorised by their cylinder layout, valves and camshafts. Wankel engines are often categorised by the number of rotors present
    11 KB (1,301 words) - 02:20, 29 October 2019
  • camshaft timing: variable nockenwellensteuerung. The initial version (retrospectively renamed "single VANOS") was solely used on the intake camshaft,
    3 KB (318 words) - 16:55, 23 July 2018
  • operating range. Piston engines normally use valves which are driven by camshafts. The cams open (lift) the valves for a certain amount of time (duration)
    27 KB (3,462 words) - 15:41, 28 December 2019
  • manifold Camshaft Camshaft bearing Camshaft fastener Camshaft follower Camshaft locking plate Camshaft pushrod Camshaft spacer ring Camshaft phase variator
    15 KB (1,492 words) - 10:01, 3 September 2019
  • consumption at low RPM. The VTEC system uses two (or occasionally three) camshaft profiles and hydraulically selects between profiles. It was invented by
    27 KB (3,865 words) - 19:16, 4 December 2019
  • camshaft (DOHC) diesel engine with indirect injection manufactured by Mercedes-Benz between 1993 and 2001. It replaced the single overhead camshaft (SOHC)
    3 KB (133 words) - 10:07, 21 November 2019
  • within the block has an advantage for physically large engines in that the camshaft drive gear is small and so suffers less from the effects of thermal expansion
    11 KB (1,301 words) - 11:10, 23 April 2019
  • perfectly flat end led to 'slamming' against a steep camshaft face. To reduce wear from the rotating camshaft, the tappets were usually circular and allowed
    13 KB (1,690 words) - 08:43, 14 November 2019
  • Overhead camshaft The camshaft(s) are located near the top of the engine, above the combustion chamber. Camless This layout uses no camshafts at all. Technologies
    8 KB (872 words) - 10:46, 16 January 2020
  • variety of displacement sizes. This overhead camshaft engine features a crossflow cylinder head design. The camshaft is driven by a toothed belt from the crankshaft
    172 KB (21,385 words) - 18:11, 9 January 2020
  • camshaft (DOHC) diesel engine with indirect injection manufactured by Mercedes-Benz between 1993 and 2001. It replaced the single overhead camshaft (SOHC)
    3 KB (100 words) - 10:12, 12 December 2019
  • 3.0 L (183 cu in) petrol V8 which was air-cooled and used an overhead camshaft which operated the valves using a 'walking beam' rocker arrangement. This
    60 KB (6,971 words) - 16:14, 16 January 2020

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)